3M Knifeless Tape for Car Wrapping and Films Vinyl Cutting

Features

1. Blade-Free Cutting: Eliminates the risk of nicks, scratches, or cuts to the underlying substrate or vehicle paint.

2. Flexible Filament: Patented design stretches slightly and turns easily in any direction to follow tight contours, curves, and body lines.

3. Clean Removal: Carrier tape and filament remove cleanly without leaving behind adhesive residue. 

• Patented design turns easily in any direction to follow contours and curves. KTS-FL23.5mm×10mDry   Design LineKTS-DL13.5mm×50mDry Single-Layer Vinyl Film• Create striping, accents and designs instead of using a knife or plotter.

• Stretches slightly and turns easily in any direction.

• Tape can be broken with hands for faster application.Perf LineKTS-PERF16.4mm×50mDry Perforated Window Film ,Laminated Film• Use to cut laminated perforated window films and create a uniform relief cut along rubber

molding before applying edge-sealing tape.Bridge LineKTS-BL112.7mm×50mDry Single or multiple vinyl layer• Used to achieve clean and uniform cuts in wide gaps between doors, fenders and rubber moldings.Tri LineKTS-TL66mm×50mDry Single-Layer Vinyl Film• Create pinstripes, gaps and butt seams instead of using a knife or plotter.

• Create different widths using 6mm, 9mm or a combination of both.

• Stretches slightly and turns easily in any direction.

• Tape can be broken with hands for faster application. KTS-TL99mm×50mDry   Precision LineKTS-PL15mm×50mWet & DryCarrier material：Green

Visual：BlueMetal / Chromed / Reflective / PPF/DI-NOC• Sharp cutting edge.

• The “sandwich” design makes cutting with the blade easier and removes the transfer tape more conveniently.

• Swivels freely for use at any angle.

Applications Glance:

1. Most Commonly Used: Finish Line (KTS-FL1/FL2) — The first choice for daily vinyl wrapping and film applications.

2. Sharpest Cut: Precision Line (KTS-PL1) — Designed for challenging, tough films such as DI-NOC, reflective films, metalized films, and PPF.

3. Widest Coverage: Bridge Line (KTS-BL1) — Ideal for covering and cutting across wide gaps, such as between doors, fenders, and around rubber seals.

4. Design‑Specific: Design Line (KTS-DL1) — Used for creative pinstriping, custom graphics, and decorative curved lines.

5. Window Film Specialist: Perf Line (KTS-PERF1) — Specifically engineered for use with perforated window films, leaving a precise gap for edge sealing.

6. Stripe Specialist: Tri Line (KTS-TL6 / KTS-TL9) — Creates accurate, parallel double stripes (racing stripes, etc.), with 6mm or 9mm filament spacing options.

How to Use:

1. Lay the tape over the vehicle's surface in your desired layout, aligning the filament along the section you intend to cut. Run your finger over the tape to keep it smooth and ensure it follows the cut line accurately.  

2. Apply the vinyl film over the surface, directly on top of the tape, and carefully smooth it out to eliminate any wrinkles. Be sure to place your knifeless tape line before installing any vinyl, and make sure the vinyl adheres well to the tape underneath.  

3. Cut or snap the tape a few inches from the end of the roll to detach it.  

4. Create a pull tab by folding the tape to expose the release string. Hold the fold with your finger and pull the filament upward in the direction of the trim line.  

5. Give the filament a quick tug, then slowly and carefully pull it to cut through the vinyl. You may remove the vinyl film along with the tape or separately, as preferred.  

6. Remove any excess tape left beneath the film, and run your finger over the area to ensure a complete seal.  

7. Tuck the remaining vinyl wrap into deep recesses or areas where the vinyl width is insufficient, securing it neatly in place.